Research output: Contribution to journal › Article › peer-review
Hot-pressed silicon carbide resistance to ITER-relevant thermal shock. / CHEREPANOV, Dmitrii; GOLOSOV, Mikhail; VYACHESLAVOV, Leonid et al.
In: Plasma Science and Technology, Vol. 27, No. 12, 125601, 01.12.2025.Research output: Contribution to journal › Article › peer-review
}
TY - JOUR
T1 - Hot-pressed silicon carbide resistance to ITER-relevant thermal shock
AU - CHEREPANOV, Dmitrii
AU - GOLOSOV, Mikhail
AU - VYACHESLAVOV, Leonid
AU - BAKLANOVA, Natalia
AU - RYZHKOV, Georgii
AU - POPOV, Vladimir
AU - SHOSHIN, Andrey
AU - KAZANTSEV, Sergey
AU - KASATOV, Alexandr
AU - KANDAUROV, Igor
AU - BURDAKOV, Alexandr
N1 - Hot-pressed silicon carbide resistance to ITER-relevant thermal shock / D. Cherepanov, M. Golosov, L. Vyacheslavov [et al.] // Plasma Science and Technology. – 2025. – Vol. 27. - No. 12. – P. 125601. – DOI 10.1088/2058-6272/ae117b. – EDN STMHYA. The work was partially supported by Russian Science Foundation (No. 23-19-00212).
PY - 2025/12/1
Y1 - 2025/12/1
N2 - Studies were carried out on the thermally induced erosion of silicon carbide as a result of pulsed infrared laser heating, simulating transient heat loads expected in the ITER tokamak divertor zone (laser pulse duration: ms). The critical parameters of pulsed heating that the material can withstand before the onset of erosion with loss of substance were determined. The experimentally observed damage threshold of hot-pressed silicon carbide under thermal shock of submillisecond duration corresponds to a temperature of about K, while a heat flux factor is about (the sample was initially at room temperature). This result is relevant for surfaces with low roughness ( m, m). An increase in surface roughness leads to a decrease in the resistance of ceramics to pulsed heating. For rough surface ( m, m) critical temperature of about K and heat flux factor of about were obtained. Thus, silicon carbide exhibits excellent resistance to transient heat loads as promising plasma-facing material, especially in the case of reduced surface roughness.
AB - Studies were carried out on the thermally induced erosion of silicon carbide as a result of pulsed infrared laser heating, simulating transient heat loads expected in the ITER tokamak divertor zone (laser pulse duration: ms). The critical parameters of pulsed heating that the material can withstand before the onset of erosion with loss of substance were determined. The experimentally observed damage threshold of hot-pressed silicon carbide under thermal shock of submillisecond duration corresponds to a temperature of about K, while a heat flux factor is about (the sample was initially at room temperature). This result is relevant for surfaces with low roughness ( m, m). An increase in surface roughness leads to a decrease in the resistance of ceramics to pulsed heating. For rough surface ( m, m) critical temperature of about K and heat flux factor of about were obtained. Thus, silicon carbide exhibits excellent resistance to transient heat loads as promising plasma-facing material, especially in the case of reduced surface roughness.
KW - SILICON CARBIDE
KW - PLASMA-FACING COMPONENTS
KW - LASER HEATING
KW - HIGH-TEMPERATURE CERAMICS
KW - IN SITU DIAGNOSTICS
KW - THERMAL SHOCK
UR - https://www.scopus.com/pages/publications/105033630190
UR - https://www.elibrary.ru/item.asp?id=87495662
UR - https://www.mendeley.com/catalogue/e5bc13e2-699d-36fc-98c0-f08df6c67c12/
U2 - 10.1088/2058-6272/ae117b
DO - 10.1088/2058-6272/ae117b
M3 - Article
VL - 27
JO - Plasma Science and Technology
JF - Plasma Science and Technology
SN - 1009-0630
IS - 12
M1 - 125601
ER -
ID: 76001410