Standard

Influence of lithium oxide excess and alumina on grain boundary resistance of Li6.75La3Zr1.75Nb0.25O12 solid electrolyte. / Dobretsov, Egor A.; Mateyshina, Yulia G.; Uvarov, Nikolai F.

в: Solid State Ionics, Том 299, 01.01.2017, стр. 55-59.

Результаты исследований: Научные публикации в периодических изданияхстатьяРецензирование

Harvard

APA

Vancouver

Dobretsov EA, Mateyshina YG, Uvarov NF. Influence of lithium oxide excess and alumina on grain boundary resistance of Li6.75La3Zr1.75Nb0.25O12 solid electrolyte. Solid State Ionics. 2017 янв. 1;299:55-59. doi: 10.1016/j.ssi.2016.09.014

Author

Dobretsov, Egor A. ; Mateyshina, Yulia G. ; Uvarov, Nikolai F. / Influence of lithium oxide excess and alumina on grain boundary resistance of Li6.75La3Zr1.75Nb0.25O12 solid electrolyte. в: Solid State Ionics. 2017 ; Том 299. стр. 55-59.

BibTeX

@article{035011a67222448f91fec6b739a9de37,
title = "Influence of lithium oxide excess and alumina on grain boundary resistance of Li6.75La3Zr1.75Nb0.25O12 solid electrolyte",
abstract = "Lithium oxide excess and powder bed method are conventionally used for synthesis of lithium-conducting solid electrolytes with cubic garnet structure. In this work Li6.75La3Zr1.75Nb0.25O12 garnet was sintered at 1200 °C on alumina and zirconia supports with controlled amount of lithium oxide excess. It was found that the powder bed method did not prevent garnet pellets from alumina contamination. The quantity of aluminum penetrated into samples correlated with the amount of lithium oxide excess added and varied from 0.2 to 0.5 wt%, as indicated by ICP AES. In contrast to alumina, zirconia did not affect chemical composition of the pellets. Taking this into account to avoid any alumina contamination a modified powder bed method was developed. However, non-contaminated samples showed lower density after sintering when compared to contaminated ones. Lithium oxide excess in the samples is likely to react with the alumina with formation of eutectic that melts at 1200 °C. The liquid eutectic phase acts as a sintering aid and promotes densification up to relative densities of 96%. Electrical properties of the pellets were measured by EIS technique. Bulk conductivity of the dense pellets was 5 × 10− 4 S/cm at 25 °C with the activation energy of 0.3 eV and depends on density. Due to grain boundary resistance dc-conductivity of pellets was lower than 10− 8 S/cm at 25 °C with the activation energy of 0.8 eV. Possible reasons of high grain boundary resistance are discussed.",
keywords = "Garnet, Ionic conduction, Lithium, Solid electrolyte, LI ION CONDUCTORS, CONDUCTIVITY, GARNET, AL",
author = "Dobretsov, {Egor A.} and Mateyshina, {Yulia G.} and Uvarov, {Nikolai F.}",
year = "2017",
month = jan,
day = "1",
doi = "10.1016/j.ssi.2016.09.014",
language = "English",
volume = "299",
pages = "55--59",
journal = "Solid State Ionics",
issn = "0167-2738",
publisher = "Elsevier Science B.V.",

}

RIS

TY - JOUR

T1 - Influence of lithium oxide excess and alumina on grain boundary resistance of Li6.75La3Zr1.75Nb0.25O12 solid electrolyte

AU - Dobretsov, Egor A.

AU - Mateyshina, Yulia G.

AU - Uvarov, Nikolai F.

PY - 2017/1/1

Y1 - 2017/1/1

N2 - Lithium oxide excess and powder bed method are conventionally used for synthesis of lithium-conducting solid electrolytes with cubic garnet structure. In this work Li6.75La3Zr1.75Nb0.25O12 garnet was sintered at 1200 °C on alumina and zirconia supports with controlled amount of lithium oxide excess. It was found that the powder bed method did not prevent garnet pellets from alumina contamination. The quantity of aluminum penetrated into samples correlated with the amount of lithium oxide excess added and varied from 0.2 to 0.5 wt%, as indicated by ICP AES. In contrast to alumina, zirconia did not affect chemical composition of the pellets. Taking this into account to avoid any alumina contamination a modified powder bed method was developed. However, non-contaminated samples showed lower density after sintering when compared to contaminated ones. Lithium oxide excess in the samples is likely to react with the alumina with formation of eutectic that melts at 1200 °C. The liquid eutectic phase acts as a sintering aid and promotes densification up to relative densities of 96%. Electrical properties of the pellets were measured by EIS technique. Bulk conductivity of the dense pellets was 5 × 10− 4 S/cm at 25 °C with the activation energy of 0.3 eV and depends on density. Due to grain boundary resistance dc-conductivity of pellets was lower than 10− 8 S/cm at 25 °C with the activation energy of 0.8 eV. Possible reasons of high grain boundary resistance are discussed.

AB - Lithium oxide excess and powder bed method are conventionally used for synthesis of lithium-conducting solid electrolytes with cubic garnet structure. In this work Li6.75La3Zr1.75Nb0.25O12 garnet was sintered at 1200 °C on alumina and zirconia supports with controlled amount of lithium oxide excess. It was found that the powder bed method did not prevent garnet pellets from alumina contamination. The quantity of aluminum penetrated into samples correlated with the amount of lithium oxide excess added and varied from 0.2 to 0.5 wt%, as indicated by ICP AES. In contrast to alumina, zirconia did not affect chemical composition of the pellets. Taking this into account to avoid any alumina contamination a modified powder bed method was developed. However, non-contaminated samples showed lower density after sintering when compared to contaminated ones. Lithium oxide excess in the samples is likely to react with the alumina with formation of eutectic that melts at 1200 °C. The liquid eutectic phase acts as a sintering aid and promotes densification up to relative densities of 96%. Electrical properties of the pellets were measured by EIS technique. Bulk conductivity of the dense pellets was 5 × 10− 4 S/cm at 25 °C with the activation energy of 0.3 eV and depends on density. Due to grain boundary resistance dc-conductivity of pellets was lower than 10− 8 S/cm at 25 °C with the activation energy of 0.8 eV. Possible reasons of high grain boundary resistance are discussed.

KW - Garnet

KW - Ionic conduction

KW - Lithium

KW - Solid electrolyte

KW - LI ION CONDUCTORS

KW - CONDUCTIVITY

KW - GARNET

KW - AL

UR - http://www.scopus.com/inward/record.url?scp=84995957144&partnerID=8YFLogxK

U2 - 10.1016/j.ssi.2016.09.014

DO - 10.1016/j.ssi.2016.09.014

M3 - Article

AN - SCOPUS:84995957144

VL - 299

SP - 55

EP - 59

JO - Solid State Ionics

JF - Solid State Ionics

SN - 0167-2738

ER -

ID: 10320400