Standard

Method of Heat Flux Measurement in Solid Fuel Flames Using Semiconductor Sensors. / Trubachev, S. A.; Korobeinichev, O. P.; Shmakov, A. G. et al.

In: Combustion, Explosion and Shock Waves, Vol. 60, No. 2, 02.04.2024, p. 185-192.

Research output: Contribution to journalArticlepeer-review

Harvard

Trubachev, SA, Korobeinichev, OP, Shmakov, AG & Sagitov, AR 2024, 'Method of Heat Flux Measurement in Solid Fuel Flames Using Semiconductor Sensors', Combustion, Explosion and Shock Waves, vol. 60, no. 2, pp. 185-192. https://doi.org/10.1134/S0010508224020059

APA

Trubachev, S. A., Korobeinichev, O. P., Shmakov, A. G., & Sagitov, A. R. (2024). Method of Heat Flux Measurement in Solid Fuel Flames Using Semiconductor Sensors. Combustion, Explosion and Shock Waves, 60(2), 185-192. https://doi.org/10.1134/S0010508224020059

Vancouver

Trubachev SA, Korobeinichev OP, Shmakov AG, Sagitov AR. Method of Heat Flux Measurement in Solid Fuel Flames Using Semiconductor Sensors. Combustion, Explosion and Shock Waves. 2024 Apr 2;60(2):185-192. doi: 10.1134/S0010508224020059

Author

Trubachev, S. A. ; Korobeinichev, O. P. ; Shmakov, A. G. et al. / Method of Heat Flux Measurement in Solid Fuel Flames Using Semiconductor Sensors. In: Combustion, Explosion and Shock Waves. 2024 ; Vol. 60, No. 2. pp. 185-192.

BibTeX

@article{4b0e5d5e31f34272a3100f43d3d09211,
title = "Method of Heat Flux Measurement in Solid Fuel Flames Using Semiconductor Sensors",
abstract = "Abstract: The total and radiative heat fluxes from the flame to the burning surface of a solid fuel (polymethylmethacrylate) slab for horizontal flame spread over the fuel surface were first quantitatively measured using two water-cooled miniature (2.3 × 2.3 mm) sensors mounted inside the slab. The design of the water cooling of 2 × 2 × 0.5 mm sensors (greenTEG AG) allows their placement directly in the combustion zone. Radiative heat flux was measured by a sensor with a protective ZnSe window, and the total heat flux was measured by a similar sensor without a protective window. The conductive heat flux determined using sensors was compared with that calculated from the data of polymethylmethacrylate flame temperature measurements using thin thermocouples. The maximum radiative and total heat fluxes from the flame to the polymethylmethacrylate surface measured by the heat flux sensors were 30–35 and 70–75 kW/m2, respectively.",
keywords = "conductive heat flux, fire, flame spread, heat flux sensor, polymethylmethacrylate, radiative heat flux",
author = "Trubachev, {S. A.} and Korobeinichev, {O. P.} and Shmakov, {A. G.} and Sagitov, {A. R.}",
note = "This work was supported by the Russian Science Foundation (Grant No. 20-19-00295).",
year = "2024",
month = apr,
day = "2",
doi = "10.1134/S0010508224020059",
language = "English",
volume = "60",
pages = "185--192",
journal = "Combustion, Explosion and Shock Waves",
issn = "0010-5082",
publisher = "Springer New York",
number = "2",

}

RIS

TY - JOUR

T1 - Method of Heat Flux Measurement in Solid Fuel Flames Using Semiconductor Sensors

AU - Trubachev, S. A.

AU - Korobeinichev, O. P.

AU - Shmakov, A. G.

AU - Sagitov, A. R.

N1 - This work was supported by the Russian Science Foundation (Grant No. 20-19-00295).

PY - 2024/4/2

Y1 - 2024/4/2

N2 - Abstract: The total and radiative heat fluxes from the flame to the burning surface of a solid fuel (polymethylmethacrylate) slab for horizontal flame spread over the fuel surface were first quantitatively measured using two water-cooled miniature (2.3 × 2.3 mm) sensors mounted inside the slab. The design of the water cooling of 2 × 2 × 0.5 mm sensors (greenTEG AG) allows their placement directly in the combustion zone. Radiative heat flux was measured by a sensor with a protective ZnSe window, and the total heat flux was measured by a similar sensor without a protective window. The conductive heat flux determined using sensors was compared with that calculated from the data of polymethylmethacrylate flame temperature measurements using thin thermocouples. The maximum radiative and total heat fluxes from the flame to the polymethylmethacrylate surface measured by the heat flux sensors were 30–35 and 70–75 kW/m2, respectively.

AB - Abstract: The total and radiative heat fluxes from the flame to the burning surface of a solid fuel (polymethylmethacrylate) slab for horizontal flame spread over the fuel surface were first quantitatively measured using two water-cooled miniature (2.3 × 2.3 mm) sensors mounted inside the slab. The design of the water cooling of 2 × 2 × 0.5 mm sensors (greenTEG AG) allows their placement directly in the combustion zone. Radiative heat flux was measured by a sensor with a protective ZnSe window, and the total heat flux was measured by a similar sensor without a protective window. The conductive heat flux determined using sensors was compared with that calculated from the data of polymethylmethacrylate flame temperature measurements using thin thermocouples. The maximum radiative and total heat fluxes from the flame to the polymethylmethacrylate surface measured by the heat flux sensors were 30–35 and 70–75 kW/m2, respectively.

KW - conductive heat flux

KW - fire

KW - flame spread

KW - heat flux sensor

KW - polymethylmethacrylate

KW - radiative heat flux

UR - https://www.scopus.com/record/display.uri?eid=2-s2.0-85206496594&origin=inward&txGid=0e9057ac9b3308a3ddaab82ccf5c6073

UR - https://www.mendeley.com/catalogue/e2576912-a112-3bac-93fb-553ab1c854cf/

U2 - 10.1134/S0010508224020059

DO - 10.1134/S0010508224020059

M3 - Article

VL - 60

SP - 185

EP - 192

JO - Combustion, Explosion and Shock Waves

JF - Combustion, Explosion and Shock Waves

SN - 0010-5082

IS - 2

ER -

ID: 61056336