Standard

Ionic conductivity of tetra-n-butylammonium tetrafluoroborate in the MIL-101(Cr) metal-organic framework. / Ulikhin, Artem S.; Uvarov, Nikolai F.; Kovalenko, Konstantin A. et al.

In: Microporous and Mesoporous Materials, Vol. 332, 111710, 02.2022.

Research output: Contribution to journalArticlepeer-review

Harvard

APA

Vancouver

Ulikhin AS, Uvarov NF, Kovalenko KA, Fedin VP. Ionic conductivity of tetra-n-butylammonium tetrafluoroborate in the MIL-101(Cr) metal-organic framework. Microporous and Mesoporous Materials. 2022 Feb;332:111710. doi: 10.1016/j.micromeso.2022.111710

Author

BibTeX

@article{1b44074b09de42de89f551c35a7421b4,
title = "Ionic conductivity of tetra-n-butylammonium tetrafluoroborate in the MIL-101(Cr) metal-organic framework",
abstract = "Nanocomposite solid electrolytes (C4H9)4NBF4–MIL-101(Cr) based on pure components without any other additives were prepared and their structure and electrical properties were investigated as a function of temperature and concentration of the metal-organic framework MIL-101(Cr). According to the data of thermal analysis, the heat effect due to the melting of the salt in the composites strongly decreases and tends to zero at a molar fraction of MIL-101(Cr) x ≥ 0.34. This effect is assumed to be caused by the amorphization of the salt in the composites which is practically complete at high content of MIL-101(Cr). The dependence of the melting enthalpy on the molar or mass fraction of MIL-101(Cr) may be explained by filling of MIL-101(Cr) pores with the salt, provided that the salt residing outside the pores is crystalline, whereas the salt located inside the pores is amorphous. In this case, at some fraction of the MIL-101(Cr), x = xmax, all the salt will be located inside the pores, and the concentration of the salt occurring in an amorphous state reaches a maximum. At x < xmax there is a linear dependence between melting enthalpy and molar (or mass) fraction from which allows one can determine xmax and wmax values from experimental data. From these data, the volume of accessible pores was estimated as Vpore = 0.92 cm3/g corresponding to 73% of the total pore volume determined by BET adsorption method. The thermal properties fairly correlate with the X-ray diffraction data. Reflections on X-ray diffraction patterns of the composites attributed to (C4H9)4NBF4 strongly decrease with the concentration of MIL-101(Cr) and at the concentration x ≥ 0.283 practically no reflections of the salt are observed on the X-ray patterns. The electrical properties of the composites were investigated. It was shown that the concentration dependence of conductivity has a maximum at the concentration close to xmax value determined from the thermal analysis data. At x > xmax temperature dependences of conductivity are not linear in Arrhenius coordinates, no sudden conductivity change is observed due to the melting of the salt. Such conductivity behaviour is typical for amorphous electrolytes. Quantitative analysis of the concentration dependence of conductivity was done using the pore filling model and the mixing equations proposed earlier for two-phase composites. Theoretical curves obtained using the mixing equations satisfactorily fit the experimental data. The maximum value of ionic conductivity, 5∙10−4 S/cm at 135 °C, obtained for the composite 0.675(C4H9)4NBF4–0.325MIL-101(Cr) is rather high assuming that BF4− anions are the most probable charge carriers.",
keywords = "Ionic conductivity, Melting enthalpy, Metal-organic framework (MOF), MIL-101(Cr), Nanocomposite solid electrolyte, Pore filling, Stabilization of amorphous phase, Tetra-n-butylammonium tetrafluoroborate",
author = "Ulikhin, {Artem S.} and Uvarov, {Nikolai F.} and Kovalenko, {Konstantin A.} and Fedin, {Vladimir P.}",
note = "Funding Information: The work is supported by the RFBR grant No. 18-29-04039 ; and the State Assignment FWUS-2021-0007. Publisher Copyright: {\textcopyright} 2022 Elsevier Inc.",
year = "2022",
month = feb,
doi = "10.1016/j.micromeso.2022.111710",
language = "English",
volume = "332",
journal = "Microporous and Mesoporous Materials",
issn = "1387-1811",
publisher = "Elsevier",

}

RIS

TY - JOUR

T1 - Ionic conductivity of tetra-n-butylammonium tetrafluoroborate in the MIL-101(Cr) metal-organic framework

AU - Ulikhin, Artem S.

AU - Uvarov, Nikolai F.

AU - Kovalenko, Konstantin A.

AU - Fedin, Vladimir P.

N1 - Funding Information: The work is supported by the RFBR grant No. 18-29-04039 ; and the State Assignment FWUS-2021-0007. Publisher Copyright: © 2022 Elsevier Inc.

PY - 2022/2

Y1 - 2022/2

N2 - Nanocomposite solid electrolytes (C4H9)4NBF4–MIL-101(Cr) based on pure components without any other additives were prepared and their structure and electrical properties were investigated as a function of temperature and concentration of the metal-organic framework MIL-101(Cr). According to the data of thermal analysis, the heat effect due to the melting of the salt in the composites strongly decreases and tends to zero at a molar fraction of MIL-101(Cr) x ≥ 0.34. This effect is assumed to be caused by the amorphization of the salt in the composites which is practically complete at high content of MIL-101(Cr). The dependence of the melting enthalpy on the molar or mass fraction of MIL-101(Cr) may be explained by filling of MIL-101(Cr) pores with the salt, provided that the salt residing outside the pores is crystalline, whereas the salt located inside the pores is amorphous. In this case, at some fraction of the MIL-101(Cr), x = xmax, all the salt will be located inside the pores, and the concentration of the salt occurring in an amorphous state reaches a maximum. At x < xmax there is a linear dependence between melting enthalpy and molar (or mass) fraction from which allows one can determine xmax and wmax values from experimental data. From these data, the volume of accessible pores was estimated as Vpore = 0.92 cm3/g corresponding to 73% of the total pore volume determined by BET adsorption method. The thermal properties fairly correlate with the X-ray diffraction data. Reflections on X-ray diffraction patterns of the composites attributed to (C4H9)4NBF4 strongly decrease with the concentration of MIL-101(Cr) and at the concentration x ≥ 0.283 practically no reflections of the salt are observed on the X-ray patterns. The electrical properties of the composites were investigated. It was shown that the concentration dependence of conductivity has a maximum at the concentration close to xmax value determined from the thermal analysis data. At x > xmax temperature dependences of conductivity are not linear in Arrhenius coordinates, no sudden conductivity change is observed due to the melting of the salt. Such conductivity behaviour is typical for amorphous electrolytes. Quantitative analysis of the concentration dependence of conductivity was done using the pore filling model and the mixing equations proposed earlier for two-phase composites. Theoretical curves obtained using the mixing equations satisfactorily fit the experimental data. The maximum value of ionic conductivity, 5∙10−4 S/cm at 135 °C, obtained for the composite 0.675(C4H9)4NBF4–0.325MIL-101(Cr) is rather high assuming that BF4− anions are the most probable charge carriers.

AB - Nanocomposite solid electrolytes (C4H9)4NBF4–MIL-101(Cr) based on pure components without any other additives were prepared and their structure and electrical properties were investigated as a function of temperature and concentration of the metal-organic framework MIL-101(Cr). According to the data of thermal analysis, the heat effect due to the melting of the salt in the composites strongly decreases and tends to zero at a molar fraction of MIL-101(Cr) x ≥ 0.34. This effect is assumed to be caused by the amorphization of the salt in the composites which is practically complete at high content of MIL-101(Cr). The dependence of the melting enthalpy on the molar or mass fraction of MIL-101(Cr) may be explained by filling of MIL-101(Cr) pores with the salt, provided that the salt residing outside the pores is crystalline, whereas the salt located inside the pores is amorphous. In this case, at some fraction of the MIL-101(Cr), x = xmax, all the salt will be located inside the pores, and the concentration of the salt occurring in an amorphous state reaches a maximum. At x < xmax there is a linear dependence between melting enthalpy and molar (or mass) fraction from which allows one can determine xmax and wmax values from experimental data. From these data, the volume of accessible pores was estimated as Vpore = 0.92 cm3/g corresponding to 73% of the total pore volume determined by BET adsorption method. The thermal properties fairly correlate with the X-ray diffraction data. Reflections on X-ray diffraction patterns of the composites attributed to (C4H9)4NBF4 strongly decrease with the concentration of MIL-101(Cr) and at the concentration x ≥ 0.283 practically no reflections of the salt are observed on the X-ray patterns. The electrical properties of the composites were investigated. It was shown that the concentration dependence of conductivity has a maximum at the concentration close to xmax value determined from the thermal analysis data. At x > xmax temperature dependences of conductivity are not linear in Arrhenius coordinates, no sudden conductivity change is observed due to the melting of the salt. Such conductivity behaviour is typical for amorphous electrolytes. Quantitative analysis of the concentration dependence of conductivity was done using the pore filling model and the mixing equations proposed earlier for two-phase composites. Theoretical curves obtained using the mixing equations satisfactorily fit the experimental data. The maximum value of ionic conductivity, 5∙10−4 S/cm at 135 °C, obtained for the composite 0.675(C4H9)4NBF4–0.325MIL-101(Cr) is rather high assuming that BF4− anions are the most probable charge carriers.

KW - Ionic conductivity

KW - Melting enthalpy

KW - Metal-organic framework (MOF)

KW - MIL-101(Cr)

KW - Nanocomposite solid electrolyte

KW - Pore filling

KW - Stabilization of amorphous phase

KW - Tetra-n-butylammonium tetrafluoroborate

UR - http://www.scopus.com/inward/record.url?scp=85123700666&partnerID=8YFLogxK

UR - https://www.mendeley.com/catalogue/8b75a62f-4d5f-3e10-ba4e-fcb0e83fbab2/

U2 - 10.1016/j.micromeso.2022.111710

DO - 10.1016/j.micromeso.2022.111710

M3 - Article

AN - SCOPUS:85123700666

VL - 332

JO - Microporous and Mesoporous Materials

JF - Microporous and Mesoporous Materials

SN - 1387-1811

M1 - 111710

ER -

ID: 35380180