Standard

Determination of the parameters of an axial pico-hydroturbine for various operating regimes. / Shtork, S. I.; Litvinov, I. V.; Gorelikov, E. Yu et al.

In: Thermophysics and Aeromechanics, Vol. 28, No. 4, 14, 07.2021, p. 599-602.

Research output: Contribution to journalArticlepeer-review

Harvard

APA

Vancouver

Shtork SI, Litvinov IV, Gorelikov EY, Suslov DA. Determination of the parameters of an axial pico-hydroturbine for various operating regimes. Thermophysics and Aeromechanics. 2021 Jul;28(4):599-602. 14. doi: 10.1134/S0869864321040144

Author

Shtork, S. I. ; Litvinov, I. V. ; Gorelikov, E. Yu et al. / Determination of the parameters of an axial pico-hydroturbine for various operating regimes. In: Thermophysics and Aeromechanics. 2021 ; Vol. 28, No. 4. pp. 599-602.

BibTeX

@article{9a22826ba955436b98343e1ef9e9c4b9,
title = "Determination of the parameters of an axial pico-hydroturbine for various operating regimes",
abstract = "The paper presents the results of detailed experimental studies of the flow characteristics behind the impeller of an air model of a propeller-type pico-hydroturbine with an impeller diameter of 0.1 m. Using the method of laser-Doppler anemometry, distributions of two components of averaged velocities and pulsations were measured under the conditions varying from partial load to severe overload. It is shown that when the regime of hydroturbine operating deviates from the optimal one, the flow at the impeller outlet becomes swirling. Based on the data obtained, the character of evolution of the integral swirling parameter, which determines the swirling flow state, has been revealed. A trend for a sharp increase in the swirling parameter with a decrease in the air flow rate was found. Due to this increase, the degree of swirling reaches quickly a critical level at which the vortex disintegrates with the development of a central dip in the axial velocity profile and displacement of the flow to the channel walls. With an increase in the flow rate, a slower increase in the swirling parameter takes place, which remains below the threshold value even for a large overload. As a result, the maxima of the tangential velocity are located near the flow axis, and the profile of the axial velocity remains uniform over the flow cross section. Information about the flow characteristics can be used when adjusting the hydraulic unit regime to optimal conditions and developing recommendations for expanding the range of regulation of the hydroturbine operation while maintaining high efficiency.",
keywords = "axial turbine, hydroturbine efficiency, laser Doppler anemometer (LDA), pico-hydroturbine, swirling parameter",
author = "Shtork, {S. I.} and Litvinov, {I. V.} and Gorelikov, {E. Yu} and Suslov, {D. A.}",
note = "This work, including measurements of velocity fields and data analysis, was carried out with state support for scientific research conducted under the guidance of leading scientists in Russian universities (Agreement No. 075-15-20191923). As regards the design and installation of the experimental setup, the work was carried out within the framework of the state assignment to the IT SB RAS. Publisher Copyright: {\textcopyright} 2021, S.I. Shtork, I.V. Litvinov, E.Yu. Gorelikov, and D.A. Suslov.",
year = "2021",
month = jul,
doi = "10.1134/S0869864321040144",
language = "English",
volume = "28",
pages = "599--602",
journal = "Thermophysics and Aeromechanics",
issn = "0869-8643",
publisher = "PLEIADES PUBLISHING INC",
number = "4",

}

RIS

TY - JOUR

T1 - Determination of the parameters of an axial pico-hydroturbine for various operating regimes

AU - Shtork, S. I.

AU - Litvinov, I. V.

AU - Gorelikov, E. Yu

AU - Suslov, D. A.

N1 - This work, including measurements of velocity fields and data analysis, was carried out with state support for scientific research conducted under the guidance of leading scientists in Russian universities (Agreement No. 075-15-20191923). As regards the design and installation of the experimental setup, the work was carried out within the framework of the state assignment to the IT SB RAS. Publisher Copyright: © 2021, S.I. Shtork, I.V. Litvinov, E.Yu. Gorelikov, and D.A. Suslov.

PY - 2021/7

Y1 - 2021/7

N2 - The paper presents the results of detailed experimental studies of the flow characteristics behind the impeller of an air model of a propeller-type pico-hydroturbine with an impeller diameter of 0.1 m. Using the method of laser-Doppler anemometry, distributions of two components of averaged velocities and pulsations were measured under the conditions varying from partial load to severe overload. It is shown that when the regime of hydroturbine operating deviates from the optimal one, the flow at the impeller outlet becomes swirling. Based on the data obtained, the character of evolution of the integral swirling parameter, which determines the swirling flow state, has been revealed. A trend for a sharp increase in the swirling parameter with a decrease in the air flow rate was found. Due to this increase, the degree of swirling reaches quickly a critical level at which the vortex disintegrates with the development of a central dip in the axial velocity profile and displacement of the flow to the channel walls. With an increase in the flow rate, a slower increase in the swirling parameter takes place, which remains below the threshold value even for a large overload. As a result, the maxima of the tangential velocity are located near the flow axis, and the profile of the axial velocity remains uniform over the flow cross section. Information about the flow characteristics can be used when adjusting the hydraulic unit regime to optimal conditions and developing recommendations for expanding the range of regulation of the hydroturbine operation while maintaining high efficiency.

AB - The paper presents the results of detailed experimental studies of the flow characteristics behind the impeller of an air model of a propeller-type pico-hydroturbine with an impeller diameter of 0.1 m. Using the method of laser-Doppler anemometry, distributions of two components of averaged velocities and pulsations were measured under the conditions varying from partial load to severe overload. It is shown that when the regime of hydroturbine operating deviates from the optimal one, the flow at the impeller outlet becomes swirling. Based on the data obtained, the character of evolution of the integral swirling parameter, which determines the swirling flow state, has been revealed. A trend for a sharp increase in the swirling parameter with a decrease in the air flow rate was found. Due to this increase, the degree of swirling reaches quickly a critical level at which the vortex disintegrates with the development of a central dip in the axial velocity profile and displacement of the flow to the channel walls. With an increase in the flow rate, a slower increase in the swirling parameter takes place, which remains below the threshold value even for a large overload. As a result, the maxima of the tangential velocity are located near the flow axis, and the profile of the axial velocity remains uniform over the flow cross section. Information about the flow characteristics can be used when adjusting the hydraulic unit regime to optimal conditions and developing recommendations for expanding the range of regulation of the hydroturbine operation while maintaining high efficiency.

KW - axial turbine

KW - hydroturbine efficiency

KW - laser Doppler anemometer (LDA)

KW - pico-hydroturbine

KW - swirling parameter

UR - http://www.scopus.com/inward/record.url?scp=85121102401&partnerID=8YFLogxK

UR - https://www.mendeley.com/catalogue/fc3bb1bc-e90e-3478-bc53-2fd7bfa456aa/

U2 - 10.1134/S0869864321040144

DO - 10.1134/S0869864321040144

M3 - Article

AN - SCOPUS:85121102401

VL - 28

SP - 599

EP - 602

JO - Thermophysics and Aeromechanics

JF - Thermophysics and Aeromechanics

SN - 0869-8643

IS - 4

M1 - 14

ER -

ID: 34976538